princess slip | Tea in a Teacup

Posts Tagged ‘princess slip’

Titanic Panic! – Making a Princess Slip or Petticoat

Posted in 20th Century, Edwardian era, Historical Costumes, Sewing, tagged 1912, combinations, corset cover, edwardian costumes, edwardian undergarments, late edwardian, petticoat, princess slip, Titanic, Titanic-era fashion on November 28, 2016| 6 Comments »

Corset Covers and Bust Ruffles, and White Petticoats, from a Sears catalogue, c. 1912.

Corset Covers and Bust Ruffles, and White Underskirts, from a Sears catalogue, c. 1912.

My panic is rising in my quest to finish off the raft of undergarments required for a Titanic evening costume.

As the list of undergarments required for a Victorian woman increased during the length of the 19th century, new “combinations” were invented to try and limit the sheer quantity of them. There were an almost exhaustive range of these undergarment items that were combined during the late Victorian and Edwardian periods; from chemise-and-corset cover, to corset cover-and-skirt/drawers, to brassiere-and-bust improver. We have already examined the chemise-drawer combinations, but there was also the combination of the corset cover and petticoat, which became known as a “princess slip”.

An Edwardian petticoat, c. 1910-1915, from The MET Museum.

Princess slips of the time tended to have a series of long panels (often either 6 and 8), with or without a waist seam. There was generally a lightly gathered frill at the knee, which was not very full, especially as the width of gowns was decreasing into the 1910s. The frill was very often trimmed with lace or could be a whole embroidered lace panel fixed to the bottom of the petticoat. Lace often adorned the top of the princess slip as well, which was used instead of fabric at the shoulder straps. The neckline could have a ribbon drawstring to help adjust it properly around the neck, and the princess slip generally reached to the ankle area.

Pattern

I did not use a pattern for this princess slip, but instead relied on what I could see from pictures of surviving extants online.

The petticoat pictured below was one of the sources I used in my design. Some of the design features that I liked were the large insertion lace around the neckline, and a smaller row of lace/ribbon to draw in the neck. The knee length frill and the back opening placket were also features I wanted to include in my garment.

An Edwardian Petticoat, front view – from Antique Dress.

An Edwardian Petticoat, back view – from Antique Dress.

There are more detailed pictures of this particular garment on the Antique Dress website, which is in the “Sources” below.

My princess slip was made from white cotton lawn, and various different types of cotton lace.

Construction Steps

Step One: I decided that the best way to do this was to do a bit of draping. Initially I was going to do a side panel, which went over each shoulder, and then a front/back panel (with the centre back having a button placket). Unfortunately I underestimated how much material would need to go under my arm, so I added an “underarm side panel” in addition to the side front panel I had already cut out.

I cut out the basic pattern shapes and then pinned them together. After I laid it on the dressmakers form, (which was set to my corseted waistline) I realised I had to alter some of the seam lines as the grainline did not sit properly.

The front, pinned together. You can see the centre front fold line.

The side, pinned together. You can see the underarm panel I cut later.

The back, pinned together, allowing a bit extra for the back button placket.

Step Two: I sewed all the seams and then flat-felled the raw edges.

The seams flat-felled. The top seam is how it looks from the inside, and the bottom seam is how it looks from the outside.

The seams flat-felled. Hard to see, but the top seam is how it looks from the inside, and the bottom seam is how it looks from the outside.

Step Three: I wanted to put a wide insertion of lace in the front neckline. I pinned it to fit, adjusting the corners to a mitred edge, and making sure that the resulting angle would go over the shoulders correctly. Then I topstitched it to the top of the garment. The raw edges of the lawn on the underside were trimmed and turned under and slipstitched down.

The finished neckline, showing the wide insertion lace with mitred corners.

Step Four: The neckline was then finished with a row of large entreduex and a row of lace. These were sewn together in the same manner as is done in heirloom sewing, with a small tight row of zigzag stitches. Any raw edges were trimmed back to the row of zigzag stitches.

The finished neckline. A ribbon was threaded through the large entredeux.

The finished neckline. A ribbon was threaded through the large entreduex, and then tied in a bow at the centre front.

Step Five: The armhole was finished with the same lace as around the neckline. The raw edges were turned under and sewn in a small hem.

The lace finishing the armhole.

Step Six: The centre back (which had been cut on the selvedge line) was finished with a button placket by folding over 1 inch of the edge of the fabric. Buttonholes were then sewn and corresponding buttons attached.

The button placket. The ribbon threaded through the entreduex is attached at the centre back so as not to come undone.

Step Seven: The bottom frill was cut 15 inches deep, and finished with the same large insertion lace as used at the neckline, plus another large row of broider anglaise. The large insertion lace was sewn in the normal way, topstitched onto the fabric and then the material cut away behind the insertion. The raw edges were trimmed and turned under to form a small hem.

The bottom of the frill is edged with a row of insertion lace and a row of broider anglaise.

The broider anglaise was sewn right sides together onto the bottom of the lace insertion, and then the raw edges trimmed and neatened with a small zigzag stitch.

Step Eight: The frill was gathered and then sewn to the bottom of the slip, just below the knee level.

The frill; trimmed, gathered and attached. The total length of the frill is 15 inches. The lace is attached at the 10 inch mark.

Step Nine: A row of ribbon insertion lace was topstitched around the bottom of the slip, but above the gathered frill. The fabric behind this insertion can be cut away, and often was in extant examples, however I didn’t do that this time.